Cleaning up Old door hardware

I came across this wonderful article about cleaning up old door hardware on Design sponge. I have lived in this house for 28 years and there are a few doors that could use a facelift so I will have add them to my do list of a million things to do.
http://www.designsponge.com/2013/01/before-and-after-cleaning-vintage-hardware.html#more-162307

The good news is that stripping and cleaning old metal hardware is really easy and more or less free! It’s a small project, but these details go a long way toward making your whole space feel clean, polished and fresh. All you need are a few basic supplies(that you might already have), and you’ll be on your way to beautiful hardware that nobody will ever know endured such a traumatic past.

Supplies needed:


For a doorknob, the first thing you’ll need to do is remove the knob. There should be a small screw at the base of the knob holding it to a central rod that runs through the mortise mechanism inside the door. After the screw is removed, it should be easy to slide off the knob.


Then expose the screws on the backplate. Usually, even with many layers of paint, it’s easy to discern where the screws should be, so I find it’s best to scrape away the paint with an X-Acto knife to expose the head. Then use a manual screwdriver (screws on old hardware usually require a small flathead) to remove the screws. Though it might seem like an electric screwdriver would be faster, electric screwdrivers have a tendency to strip old, stuck screws. Apply pressure, take your time and the screw should come loose easily enough.

After you’ve removed all the screws, pry off the backplates. If you don’t want to re-paint the door when you’re done, use your X-Acto knife to cut into the paint around the backplate so that the plate doesn’t take big chunks of paint with it.

For extra points, remove the mortise inside the door, too. This one was removed at some point and replaced upside down (and, consequently, the backplates were then reinstalled upside down!), so it was extra-important to remove this one and replace it correctly.

When you’re done, sweep up any loose paint on the floor. Older layers of paint may be lead-based, so it’s not a good idea to leave pieces lying around where pets or children might decide to munch on them.

There are many stripping products on the market (such as corrosive paint strippers and heat guns), but all you really need for a project like this is a decent sized old pot. It’s probably not a great idea to prepare food in this pot when you’re done, so I picked this one up at a thrift store for $5. If you think older layers of paint might be lead-based, this project is safer with a lidded crockpot on the middle setting overnight. You can often find old crockpots at thrift stores that work great for projects like this!

Fill the pot with water and a few tablespoons of dish soap (no need to be exact!), and throw your painty hardware and screws in! Cover the pot and keep it on low heat, enough for the water to heat up but not enough to boil. Then just leave it there for several hours. You should be able to see the paint begin to bubble and separate from the hardware within a few hours, but it’s good to let it all marinate for about 6-8. Keep an eye on it while you occupy your time with something more exciting, like staring in the mirror and whispering self-affirming statements to your reflection.

When the hardware has been heated for a while, remove it with tongs directly into a bowl of ice water. I’ve skipped this step in the past, but it does seem to make the paint extra-easy to remove, as well as making the hardware easy to handle immediately.

Then just move over to the sink and start removing your paint! Most of it should come off easily with your fingers and the rough side of a sponge, although paint might still cling to small crevices (like screw holes). I like to keep my X-Acto blade (or a flathead screwdriver, or something rigid and pointy) handy to carefully peel off these difficult parts. Be careful, here — you don’t want to scratch the finish! Or cut off a finger.

After you’ve sponged everything down and removed all the paint, dry it off with a towel, and you could be done! If your hardware is on the newer side, it may be nice to give it a final scrub with a product such as Bar Keeper’s Friend. This stuff is mega-powerful, though, so it’s a good idea to start with the back of a backplate or another area that won’t be exposed, just to make sure you actually like the restored finish. For this knob set, I decided to leave the patina as is instead of trying to restore it to like-new condition.

To protect the finish from tarnishing further — or rusting if it’s going in a bathroom — you may want to hit it with a coat of clear matte varnish. And if it turns out that you totally hate the plain metal, or it just doesn’t look right with your house, you can always repaint it with a nice even coat of spray paint. Black hardware on a white door looks amazing.

Then all that’s left is to reattach it to the door, and you’re done! Now you’ll feel fancy and accomplished, and you can stop hating whatever monster(s) caused this mess in the first place!

Daniel Kanter is a freelance writer and designer who blogs about his home at Manhattan Nest.